Cost Of Installing Overhead Dvd Player

Posted on 21.08.201922.08.2017by admin

If you’re a fan of classic science fiction from the likes of Ray Bradbury, Isaac Asimov, and Robert A. Heinlein, you’re in luck. Archive.org now has a massive collection of the magazine Galaxy Science Fiction for you to peruse for free.

Cost Of Installing Overhead Dvd Player
Installing Overhead Dvd Player

Ceiling Mount DVD Install. By joining our community, at no cost. As i want this dvd player off when the ignition is off.

The Internet Arcade Has 900 Classic Arcade Games You Can Play for Free

If you need to take a break and have some fun, the Internet Archive has gathered over 900 classic…

Read more Read

The collection has over 350 issues spanning from 1950 to 1976, and even includes an early version of Ray Bradbury’s Fahrenheit 451, The Fireman, as well as Isaac Asimov’s The Caves of Steel, and Afred Bester’s The Stars My Destination. While the collection isn’t quite the entire run of GSF, it’s probably more than enough to keep you busy. Besides, you can’t beat free. You can browse through the entire collection at the link below.

Galaxy Science Fiction collectionArchive.org via The Verge

You want to make travel time more enjoyable for you and your little ones, so you decided on an entertainment system. Deciding to install an overhead DVD system can be rewarding in the long run, but complex in the beginning. A novice can complete this type of project, but some experience in this subject will make the process go more quickly. Either way you will save installation cost. You may also be able to seek installation support through the company you purchased the system from. Take your time and it will pay off on those long family travel trips.

Step 1

Decide where you want to place the overhead DVD system. Determine the best position for everyone in the rear to easily see the DVD screen. You may need to remove your dome light.

Step 2

Outline the bracket that came with the overhead DVD player on the headliner of your vehicle where you decided to place the overhead DVD player. Makes sure the outline is centered from both sides of the vehicle.

Step 3

Partially drop the headliner of the vehicle. Only one side of the headliner needs to be dropped just enough to bring the wires through. Unscrew the driver's side or the passenger side sun visor that the fuse box is located on. Disconnect the vanity light by gently pulling the connectors. Pry off the upper and lower pillar trim panel on the same side from which you removed the sun visor with the flathead screwdriver. You may need to remove the seat belt if it is attached to the upper pillar. The seat belt is usually secured with a head or Torx bolt. Remove any screws and retaining clips. Unscrew the kick panel over the fuse box and place the panel to the side.

Step 4

Download pixelview tv tuner software. Cut out the outline on the headliner. Ensure that a support beam runs across the area where you intend to mount the overhead DVD player. If there is no beam, you will need to glue the wood rail to the roof of the vehicle.

Step 5

Use the bracket to mark at least four drill holes on the wood or support beam. Make sure to drill the holes centered on the beam.

Step 6

Run the wires that came with the overhead DVD player through the headliner. Leave enough slack to connect to the DVD player. Follow the instructions and use the hardware that came with the overhead DVD player. Some units will requires you to connect all wiring to the DVD player before mounting. You will hide the wires behind the panels you removed.

Step 7

Mount the bracket carefully using the short screws that came with the overhead DVD player. Connect the dome wires to the appropriate wires as described in the instructions that came with the overhead DVD player.

Step 8

Connect the power and audio wires as detailed in the manufacturer's instructions. All wires must be connected to a 12-volt source except the black one. It must be grounded. You can use any screw to ground the black wire. Use the wire crimper to cut the wires and use the electrical tape to secure wire connections. Place the FM modulator under the seat nearest to where you took off the panels.

Run the audio cable to the FM modulator. Set the modulator at one of the radio signals stated on the modulator. Securely place the wires loosely where the panels will be replaced. Secure all panels, seat belt and headliner back into place.

Warnings

Do not over tighten the DVD player. It could cause the screen to warp.
Installation can take up to four hours or more.